This page was exported from Lead2pass New Updated Exam Questions [ https://www.getfreevce.com ] Export date:Mon Dec 23 11:02:45 2024 / +0000 GMT ___________________________________________________ Title: [PDF&VCE] Lead2pass 2016 New Cisco 100-105 Braindump Free Download (21-40) --------------------------------------------------- 2016 September Cisco Official New Released 100-105 Dumps in Lead2pass.com! 100% Free Download! 100% Pass Guaranteed! We offers the most current and best training materials of the 100-105 certification Q&A , Practice Software, Study Packs, Preparation Labs and Audio Training you are looking for. Our online certification training offers you quick and cost-efficient way to train and become a certified professional in IT industry. Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/100-105.html QUESTION 21Refer to the exhibit. The MAC address table is shown in its entirety. The Ethernet frame that is shown arrives at the switch. What two operations will the switch perform when it receives this frame? (Choose two.) A.    The switch will not forward a frame with this destination MAC address.B.    The MAC address of 0000.00aa.aaaa will be added to the MAC Address Table.C.    The MAC address of ffff.ffff.ffff will be added to the MAC address table.D.    The frame will be forwarded out all active switch ports except for port fa0/0.E.    The frame will be forwarded out fa0/0 and fa0/1 only.F.    The frame will be forwarded out all the ports on the switch. Answer: BDExplanation:If the switch already has the MAC address in its table for the destination, it will forward the frame directly to the destination port. If it was not already in its MAC table, then they frame would have been flooded out all ports except for the port that it came from. QUESTION 22On a Cisco switch, which protocol determines if an attached VoIP phone is from Cisco or from another vendor? A.    RTPB.    TCPC.    CDPD.    UDP Answer: CExplanation:The Cisco Unified IP Phone uses CDP to communicate information such as auxiliary VLAN ID, per port power management details, and Quality of Service (QoS) configuration information with the Cisco Catalyst switch. QUESTION 23Refer to the exhibit. What must be configured to establish a successful connection from Host A to switch SW-A through router RT-A?A.    VLAN 1 on RT-AB.    IP routing on SW-AC.    default gateway on SW-AD.    crossover cable connecting SW-A and RT-A Answer: CExplanation:In order for the switch to reach networks that are not local, such as networks attached to different interfaces of the router, it will need to set its default gateway to be the IP address of the attached router. QUESTION 24A switch receives a frame on one of its ports. There is no entry in the MAC address table for the destination MAC address. What will the switch do with the frame? A.    drop the frameB.    forward it out of all ports except the one that received itC.    forward it out of all portsD.    store it until it learns the correct port Answer: BExplanation:Understanding this concept is prime for understanding that when switch receives the data frame from the host not having the MAC address already in the MAC table, it will add the MAC address to the source port on the MAC address table and sends the data frame. If the switch already has the MAC address in it's table for the destination, it will forward the frame directly to the destination port. If it was not already in it's MAC table, then they frame would have been flooded out all ports except for the port that it came from. QUESTION 25At which layer of the OSI model does the protocol that provides the information that is displayed by the show cdp neighbors command operate? A.    applicationB.    transportC.    networkD.    physicalE.    data link Answer: EExplanation:CDP is a device discovery protocol that runs over Layer 2 (the data link layer) on all Cisco- manufactured devices (routers, bridges, access servers, and switches) and allows network management applications to discover Cisco devices that are neighbors of already known devices. With CDP, network management applications can learn the device type and the Simple Network Management Protocol (SNMP) agent address of neighboring devices running lower-layer, transparent protocols. QUESTION 26Which two characteristics apply to Layer 2 switches? (Choose two.) A.    increases the number of collision domainsB.    decreases the number of collision domainsC.    implements VLAND.    decreases the number of broadcast domainsE.    uses the IP address to make decisions for forwarding data packets Answer: ACExplanation:Layer 2 switches offer a number of benefits to hubs, such as the use of VLANs and each switch port is in its own separate collision domain, thus eliminating collisions on the segment. QUESTION 27Which two commands will display the current IP address and basic Layer 1 and 2 status of an interface? (Choose two.) A.    router#show versionB.    router#show ip interfaceC.    router#show protocolsD.    router#show controllersE.    router#show running-config Answer: BC QUESTION 28Which two characteristics describe the access layer of the hierarchical network design model? (Choose two.) A.    layer 3 supportB.    port securityC.    redundant componentsD.    VLANsE.    PoE Answer: BDExplanation:The primary function of an access-layer is to provide network access to the end user.The hardware and software attributes of the access layer that support high availability include security services for additional security against unauthorized access to the network through the use of tools such as 802.1x, port security, DHCP snooping, Dynamic ARP Inspection, and IP Source Guard. QUESTION 29Refer to the topology and switching table shown in the graphic. Host B sends a frame to Host C. What will the switch do with the frame? A.    drop the frameB.    send the frame out all ports except port 0/2C.    return the frame to Host BD.    send an ARP request for Host CE.    send an ICMP Host Unreachable message to Host BF.    record the destination MAC address in the switching table and send the frame directly to Host C Answer: B QUESTION 30What is the purpose of assigning an IP address to a switch? A.    provides local hosts with a default gateway addressB.    allows remote management of the switchC.    allows the switch to respond to ARP requests between two hostsD.    ensures that hosts on the same LAN can communicate with each other Answer: BExplanation:Switch is a layer 2 device and doesn't use network layer for packet forwarding. The IP address may be used only for administrative purposes such as Telnet access or for network management purposes. QUESTION 31Which three statements are true about the operation of a full-duplex Ethernet network? (Choose three.) A.    There are no collisions in full-duplex mode.B.    A dedicated switch port is required for each full-duplex node.C.    Ethernet hub ports are preconfigured for full-duplex mode.D.    In a full-duplex environment, the host network card must check for the availability of the network media before transmitting.E.    The host network card and the switch port must be capable of operating in full-duplex mode. Answer: ABEExplanation:Half-duplex Ethernet is defined in the original 802.3 Ethernet and Cisco says you only use one wire pair with a digital signal running in both directions on the wire. It also uses the CSMA/CD protocol to help prevent collisions and to permit retransmitting if a collision does occur. If a hub is attached to a switch, it must operate in half-duplex mode because the end stations must be able to detect collisions. Half-duplex Ethernet--typically 10BaseT--is only about 30 to 40 percent efficient as Cisco sees it, because a large 10BaseT network will usually only give you 3- to 4Mbps--at most. Full-duplex Ethernet uses two pairs of wires, instead of one wire pair like half duplex. Also, full duplex uses a point-to-point connection between the transmitter of the transmitting device and the receiver of the receiving device, which means that with full-duplex data transfer, you get a faster data transfer compared to half duplex. And because the transmitted data is sent on a different set of wires than the received data, no collisions occur. The reason you don't need to worry about collisions is because now Full-duplex Ethernet is like a freeway with multiple lanes instead of the single-lane road provided by half duplex. Full-duplex Ethernet is supposed to offer 100 percent efficiency in both directions; this means you can get 20Mbps with a 10Mbps Ethernet running full duplex, or 200Mbps for FastEthernet. QUESTION 32Which router command can be used to determine the status of Serial 0/0? A.    show ip routeB.    show interfacesC.    show s0/0 statusD.    debug s0/0E.    show runF.    show version Answer: B QUESTION 33What is the subnet address of 172.16.159.159/22? A.    172.16.0.0B.    172.16.128.0C.    172.16.156.0D.    172.16.159.0E.    172.16.159.128F.    172.16.192.0 Answer: CExplanation:Converting to binary format it comes to11111111.11111111.11111100.00000000 or255.255.252.0Starting with 172.16.0.0 and having increment of 4 we get. QUESTION 34An administrator is working with the 192.168.4.0 network, which has been subnetted with a /26 mask. Which two addresses can be assigned to hosts within the same subnet? (Choose two.) A.    192.168.4.61B.    192.168.4.63C.    192.168.4.67D.    192.168.4.125E.    192.168.4.128F.    192.168.4.132 Answer: CDExplanation:Only the values of host with 67 and 125 fall within the range of /26 CIDR subnet mask, all others lie beyond it. QUESTION 35Refer to the exhibit. The internetwork is using subnets of the address 192.168.1.0 with a subnet mask of 255.255.255.224. The routing protocol in use is RIP version 1. Which address could be assigned to the FastEthernet interface on RouterA? A.    192.168.1.31B.    192.168.1.64C.    192.168.1.127D.    192.168.1.190E.    192.168.1.192 Answer: DExplanation: Subnet mask 255.255.255.224 with CIDR of /27 which results in 32 hosts per.192.168.1.31 is the broadcast address for sunbet '0' 192.168.1.64 is the network address for subnet '2' 192.168.1.127 is the broadcast address for subnet '3' 192.168.1.192 is the network address for subnet '6' QUESTION 36What is the network address for the host with IP address 192.168.23.61/28? A.    192.168.23.0B.    192.168.23.32C.    192.168.23.48D.    192.168.23.56E.    192.168.23.60 Answer: CExplanation:convert bit-length prefix to quad-dotted decimal representation, then from it find the number of bits used for subnetting you can find previously calculated number of subnets by separating subnets each having value of last bit used for subnet masking Find that your IP address is in which subnet, that subnet's first address is network address and last address is broadcast address. Based on above steps the answer is option C. QUESTION 37What is the best practice when assigning IP addresses in a small office of six hosts? A.    Use a DHCP server that is located at the headquarters.B.    Use a DHCP server that is located at the branch office.C.    Assign the addresses by using the local CDP protocol.D.    Assign the addresses statically on each node. Answer: DExplanation:Its best to use static addressing scheme where the number of systems is manageable rather than use dynamic protocol as it is easy to operate and manage. QUESTION 38Refer to the exhibit. The enterprise has decided to use the network address 172.16.0.0. The network administrator needs to design a classful addressing scheme to accommodate the three subnets, with 30, 40, and 50 hosts, as shown. What subnet mask would accommodate this network? A.    255.255.255.192B.    255.255.255.224C.    255.255.255.240D.    255.255.255.248E.    255.255.255.252 Answer: AExplanation:Subnet mask A i.e. 255.255.255.192 with CIDR of /26 which means 64 hosts per subnet which are sufficient to accommodate even the largest subnet of 50 hosts. QUESTION 39Which two statements describe the IP address 10.16.3.65/23? (Choose two.) A.    The subnet address is 10.16.3.0 255.255.254.0.B.    The lowest host address in the subnet is 10.16.2.1 255.255.254.0.C.    The last valid host address in the subnet is 10.16.2.254 255.255.254.0D.    The broadcast address of the subnet is 10.16.3.255 255.255.254.0.E.    The network is not subnetted. Answer: BDExplanation:The mask 255.255.254.0 (/23) used with a Class A address means that there are 15 subnet bits and 9 host bits. The block size in the third octet is 2 (256 - 254). So this makes the subnets in 0, 2, 4, 6, etc., all the way to 254. The host 10.16.3.65 is in the 2.0 subnet. The next subnet is 4.0, so the broadcast address for the 2.0 subnet is 3.255. The valid host addresses are 2.1 through 3.254 QUESTION 40Given a Class C IP address subnetted with a /30 subnet mask, how many valid host IP addresses are available on each of the subnets? A.    1B.    2C.    4D.    8E.    252F.    254 Answer: BExplanation:/30 CIDR corresponds to mask 55.255.255.252 whose binary is 11111100 which means 6 subnet bits and 2 host bits which means 62 subnets and 2 hosts per subnet. The strength of our 100-105 dumps is the constant update that we perform to keep abreast with the market trends and changes. Our 100-105 exam question is not only the best option for certification but also enhances your skill to an advance level. 100-105 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDWUdDVE1SbVBrb1k 2016 Cisco 100-105 exam dumps (All 274 Q&As) from Lead2pass: http://www.lead2pass.com/100-105.html [100% Exam Pass Guaranteed] --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2016-09-18 04:03:29 Post date GMT: 2016-09-18 04:03:29 Post modified date: 2016-09-18 04:03:29 Post modified date GMT: 2016-09-18 04:03:29 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com