[Full Version] Latest Lead2pass 100-105 Exam Free 100-105 Dumps Download (278-285)

2017 January Cisco Official New Released 100-105 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Test your preparation for Cisco 100-105 with these actual 100-105 new questions below. Exam questions are a sure method to validate one’s preparation for actual certification exam.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/100-105.html

QUESTION 278
Hotspot Question – RIPv2 Troubleshooting II
Why applications that are installed on PC’s in R2 LAN network 10.100.20.0/24 are unable to communicate with server1?

A.    A standard ACL statement that is configured on R1 is blocking the traffic sourced from Server1 network.
B.    A standard ACL statement that is configured on R2 is blocking the traffic sourced from Setver1 network.
C.    A standard ACL statement that is configured on R2 is blocking the traffic sourced from R2 LAN network.
D.    A standard ACL statement that is configured on R1 is blocking the traffic sourced from R2 LAM network

Answer: B

QUESTION 279
Hotspot Question – RIPv2 Troubleshooting II
Users complain that they are unable to reach internet sites.
You are troubleshooting internet connectivity problem at main office.
Which statement correctly identifies the problem on Router R1?

A.    Interesting traffic for NAT ACL is incorrectly configured.
B.    NAT configurations on the interfaces are incorrectly configured
C.    NAT translation statement incorrectly configured.
D.    Only static NAT translation configured for the server, missing Dynamic NAT or Dynamic NAT overloading for internal networks.

Answer: B

QUESTION 281
Hotspot Question – RIPv2 Troubleshooting II
Examine the DHCP configuration between R2 and R3; R2 is configured as the DHCP server and R3 as the client. What is the reason R3 is not receiving the IP address via DHCP?

A.    On R2. The network statement In the DHCP pool configuration is incorrectly configured.
B.    On R3. DHCP is not enabled on the interface that is connected to R2.
C.    On R2, the interface that is connected to R3 is in shutdown condition.
D.    On R3, the interface that is connected to R2 is in shutdown condition.

Answer: B

QUESTION 282
Which statement describes the effect of the overload keyword in the ip nat inside source list 90 interface ethernet 0/0 overload command?

A.    Addresses that match address list inside are translated to the IP address of the Ethernet 0/0 interface.
B.    Hosts that match access inside are translated to an address m the Ethernet 0/0 network.
C.    Hosts on the Ethernet 0/0 LAN are translated to the address pool in access list 90.
D.    Addresses that match access list 90 are translated through PAT to the IP address of the Ethernet 0/0 interface

Answer: D

QUESTION 283
Which statement describes the effect of the copy run start command on a router in enable mode?

A.    The running configuration of the router is saved to NVRAM and used during the boot process.
B.    The router reboots and loads the last saved running configuration.
C.    A copy of the running configuration of the router is sent by FTP to a designated server.
D.    A new running configuration is loaded from flash memory to the router.

Answer: D

QUESTION 284
After you configure a default route to the Internet on a router, the route is missing from the routing table. Which option describes a possible reason for the problem?

A.    The next-hop address is unreachable.
B.    The default route was configured on a passive interface.
C.    Dynamic routing is disabled.
D.    Cisco Discovery Protocol is disabled on the interface used to reach the next hop.

Answer: C

QUESTION 285
You have configured the host computers on a campus LAN to receive their DHCP addresses form the local router to be able to browse their corporate site.
Which statement about the network environment is true?

A.    It supports a DNS server for use by DHCP clients.
B.    Two host computers may be assigned the same IP address.
C.    The DNS server must be configured manually on each host.
D.    The domain name must be configured locally on each host computer.

Answer: D

These Cisco 100-105 exam questions are all a small selection of questions. If you want to practice more questions for actual 100-105 exam, use the links at the end of this document. Also you can find links for 100-105 VCE software that is great for preparation and self-assessment for Cisco 100-105 exam.

100-105 new questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDWUdDVE1SbVBrb1k

2017 Cisco 100-105 exam dumps (All 295 Q&As) from Lead2pass:

http://www.lead2pass.com/100-105.html [100% Exam Pass Guaranteed]